![]() ![]() New multiple dimmer controls are more expensive, but they talk to each other to allow controlling the intensity of a single light from multiple locations.Ĭlick here for information on the LEGALITY OF DIY ELECTRICAL WORK. If you use a 3-way dimmer switch together with a 3-way toggle switch, the second switch could not change the intensity of light but just turn it on or off. Claro Smart Switch Turns wired lights or ceiling/exhaust fans on and off Replaces existing light switch Wired or wireless 3-way/multi-location capable for. You might even want to set it to the level you want and then remove its control, even decorate over the switch so that no-one plays with it. If you put one dimmer switch on each end, outside of each of the three-way switches, you would have to have both dimmers on and the end result would be a reducing of the power of the light by the sum of the two dimmers, so if all you want to do is to reduce the strength of the light, use just one dimmer.Īll of that is to say that a simple dimmer switch cannot give you that top of the stairway, bottom of the stairway control, but can be used to reduce the intensity of the light, but you will have to remember to leave the dimmer on at all times for the rest of the system to work. ![]() This would turn on and off the whole system, as well as have the possibility of reducing the light level. What you could also do is to put a dimmer switch on the common line leading into a pair of three-way switch. A year after I wrote this page, Lutron showed me Multiple dimmer controls that can have up to 10 dimmer switches for a single light! I can't update TV shows, but I can update the web. You can however now find 3-way dimmer switches in the stores which have three wires out the back, like the three screws on the regular 3-way toggle switches, and that would replace one of the 3-way switches. The top of the stairway, bottom of the stairway reversing control would no longer work. If you simply replaced one of the three-way switches with an ordinary dimmer switch, it would no longer toggle from one line to another and would only go on or off and reduce the power of the current. It takes a pair of three-way switches as shown in the diagram to cause that re-routing of electricity that will cause the light to change whatever state it is in, on or off, to the opposite state when you reverse either one of the toggle switches. In fact a three-way switch all by itself would be of little use for your light. One is the common wire and the other two carry that common current to one line or another. That is why the three-way switch has three screws on it. So here goes.Ī three-way switch does not just turn the electricity on and off, but it switches the current from one line to another. In fact I don't think I was perfectly clear about this when I did the segment on the TV show, judging by the confusion I heard after it was broadcast. If your dimmer doesn't have terminal wires, place a hook at the end of the stripped wire, wrap around the screw, and then tighten the screw.Rebecca from Cold Lake, Alberta wants to dim her three-way switchs. Many new dimmers no longer have terminal wires and use screw terminals that might be similar to the ones on the switch you removed instead. : 3 Way Dimmer Switch 1-48 of over 1,000 results for '3 way dimmer switch' Results Amazon Basics 3-Way Smart Dimmer Switch, Neutral Wire Required, 2. If needed, use the wire stripper to remove a section of the. Examine each wire and ensure that a section is bare. You will set two sets of cables, one from the light fixture and the other. If the wires are flattened, nicked, or damaged, clip off this portion of the wire and strip a 3/4-inch fresh section. Procedure for connecting the 3-way dimmer switch wiring Start by sorting the wires in the wall socket. Straighten out any loops in the copper wires, using needle-nose pliers. The new dimmer switch will be connected to the circuit wires using wire nuts or another form of wire connector, so the circuit wires may need to be straightened. If your switch is attached via push-in fittings on the back, you can remove them by pushing a small nail into the release slot next to each push-in screw terminal, or simply clip them off with your wire cutters and re-strip them to the proper length. If that's the case, simply unscrew them and untwist the wires. Alternatively, your old switch might be connected with wire nuts. If a ground wire is also attached, disconnect it from the green ground screw. The Spruce Home Improvement Review Boardĭetach the circuit wires by loosening the screw terminals on the side of the switch and pulling the wires free. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |